- No Items in Cart.
Danfoss® E-Z Clip Field Attachable Elbow 90° 13/32 x 3/4"
Danfoss® - E-Z Clip Series Field Attachable Elbow, Carbon Steel, Female O-Ring Short Pilot, 90°, 13/32" (-8) x 3/4-16 (-8) (Pack of 2)
Representative Image Only
- WARNING
- TAA Compliant
Make your own hose assemblies in minutes Reduce downtime and increase productivity Does not require hose-crimping machinery Typical applications include: Truck and bus fleets, construction equipment, military vehicles, agricultural equipment, refrigerated trucks (dairy and produce)
Use with GH134W Multi-Refrigerant Hose
Assembly InstructionsStep 1: Cut the hose. Be sure the cut is made square to the hose length.Step 2: Slip on two clips.Step 3: Oil the nipple. This MUST be done to lower the force of nipple insertion.Step 4: Insert the nipple into the hose. Be sure to wipe excess oil from the nipple and hose.Step 5: Snap the cage into the groove on the nipple.Step 6: Slide the clips over the cage arms and into the channels on each arm.Step 7: Close the clips.E-Z Clip® Completed assembly.
NOTE: Pilot O-rings are not included and must be purchased separately.
CAUTION: Failure to follow these instructions and/or the use of Weatherhead® hose with fittings supplied by other manufacturers may result in unreliable and unsafe hose assemblies, which may result in sudden or unintended escape of refrigerant gases. Personal injury and/or violations of the EPA regulations may occur as a consequence.Eaton recommends adherence to all guidelines, including EPA guidelines, concerning the services of refrigerant systems.
Danfoss® E-Z Clip Field Attachable Elbow 90° 13/32 x 3/4"
Field Attachable
13/32 (-8) "
-8
E-Z Clip Series
Female
O-Ring Short Pilot
Swivel
90 Degrees
3/4-16 (-8)
FJ5985-0808S
(-8)X(-8)
Carbon Steel
27121700
Yes
Description
Make your own hose assemblies in minutes Reduce downtime and increase productivity Does not require hose-crimping machinery Typical applications include: Truck and bus fleets, construction equipment, military vehicles, agricultural equipment, refrigerated trucks (dairy and produce)
Use with GH134W Multi-Refrigerant Hose
Assembly InstructionsStep 1: Cut the hose. Be sure the cut is made square to the hose length.Step 2: Slip on two clips.Step 3: Oil the nipple. This MUST be done to lower the force of nipple insertion.Step 4: Insert the nipple into the hose. Be sure to wipe excess oil from the nipple and hose.Step 5: Snap the cage into the groove on the nipple.Step 6: Slide the clips over the cage arms and into the channels on each arm.Step 7: Close the clips.E-Z Clip® Completed assembly.
NOTE: Pilot O-rings are not included and must be purchased separately.
CAUTION: Failure to follow these instructions and/or the use of Weatherhead® hose with fittings supplied by other manufacturers may result in unreliable and unsafe hose assemblies, which may result in sudden or unintended escape of refrigerant gases. Personal injury and/or violations of the EPA regulations may occur as a consequence.Eaton recommends adherence to all guidelines, including EPA guidelines, concerning the services of refrigerant systems.
Tech Specs
Danfoss® E-Z Clip Field Attachable Elbow 90° 13/32 x 3/4"
Field Attachable
13/32 (-8) "
-8
E-Z Clip Series
Female
O-Ring Short Pilot
Swivel
90 Degrees
3/4-16 (-8)
FJ5985-0808S
(-8)X(-8)
Carbon Steel
27121700
Yes
Restrictions
Accessories
† May Require Additional Delivery Time to Canada